-
Who's writing this
-
FAQ
-
What's the biggest mistake people make buying a used Schwing concrete pump truck?
-
Is a Schwing electric concrete pump actually worth it?
-
Do I need a concrete bucket if I've got a pump?
-
Can I haul a pump with any trailer—does a Shelby truck work?
-
How do I drill into concrete without hitting something I shouldn't?
-
Which Schwing parts should I always keep on hand?
-
What's the one thing you'd tell a first-time buyer?
-
What's the biggest mistake people make buying a used Schwing concrete pump truck?
Who's writing this
I've been handling concrete pump and parts orders—Schwing, mostly—since 2014. Over that stretch I've made roughly $23,000 worth of documented mistakes. Not bragging. Just saying the answers below aren't theoretical. They're what I learned after a customer called, annoyed, on a Friday.
FAQ
What's the biggest mistake people make buying a used Schwing concrete pump truck?
Not asking for hydraulic pump hours. I did this in 2019 on a 2007 truck. The engine read 4,200 hours, which looked reasonable. I asked about service records, the seller said 'mostly complete,' and I moved on. Two months in, the main hydraulic pump started bypassing oil. Repair: $6,400. Lost work: about a week. The rock valve on these trucks is genuinely tough—arguably the best in the industry—but a worn hydraulic system will take a good valve down with it.
Now the first thing I request is a log of hydraulic component hours and any replaced valve blocks. If the seller 'doesn't have records,' that's not a maybe. That's a red flag. A $300 inspection pays for itself ten times over. Trust me on this one, because I didn't the first time.
Is a Schwing electric concrete pump actually worth it?
For indoor jobs and sites with strict emissions rules, yes. But check the power supply before you commit. My worst mistake here was 2021: I sold an electric pump to a contractor with 240V single-phase at the site. That pump needed 480V three-phase. I said 'it needs a proper hookup.' They heard 'an extension cord.' Result: $1,800 in rewiring and a two-day delay.
Electric pumps shine where diesel noise and fumes are non-starters—tunnels, basements, hospitals. But get the electrical spec in writing. On paper. Voltage and phase spelled out. I've stopped trusting 'we'll figure it out on-site,' because honestly, nobody ever does. I thought I'd learned that in 2021. Sort of did—then a customer in 2023 made me learn it again.
Do I need a concrete bucket if I've got a pump?
Sometimes, and the sizing decision is where people get it wrong. Buckets are for small, tight pours where you can't justify setting up a boom or line pump—a footer repair, a small column, a patch. The mistake I remember most clearly: a customer in 2020 specified a 3/4-yard bucket for a job the pump was feeding at roughly 2 yards a minute. That bucket was basically a bottleneck from the first pour. We swapped it for a 1.5-yard and everything moved.
Point is: bucket size is a flow question, not a price question. And cheaping out on the bucket to save $200 changes how your crew and your customer see the whole pour. That first impression doesn't come back. It's a small thing that reads as a big thing.
Can I haul a pump with any trailer—does a Shelby truck work?
Depends on what you're actually moving. A Shelby truck or a similar hauling rig can work fine for skids, small pumps, and parts. A full truck-mounted boom pump has its own over-the-road requirements—weight, height, DOT permits. Don't assume 'I've got a truck, I'm fine.' In 2018 a buyer tried to move a 38-meter boom pump behind a rig that wasn't rated for the tongue weight. That could've gone badly. Check the weight plate, check your trailer class, and if you're over 80,000 lb GVW, look up DOT oversize/overweight rules for your state before you turn the key.
How do I drill into concrete without hitting something I shouldn't?
Scan before you drill. That's the boring answer that saves the most money. I learned it in 2017, when a 'quick' install went through a post-tension cable on a parking deck. Repair bill: $2,300, plus a call from a property manager who was, understandably, not thrilled. Post-Tensioning Institute guidance on drilling near PT systems is pretty clear—scan first, keep a safe distance from cables, and if you're unsure, use a cable-avoidance approach. ACI 318 covers the structural side; the practical rule is simpler—know what's in the concrete before the bit goes in.
Concrete looks solid. It isn't. It's full of rebar, tension cables, and conduit. A $200 scan beats a $2,300 repair every single time. That's not hyperbole. That's math.
Which Schwing parts should I always keep on hand?
The ones that fail on a Friday afternoon. For me: rock valves and wear plates first. Rubber end hoses second—cheap to stock, expensive to chase down when a pour is starting. Seals and gaskets for the main hydraulic pump third. If you're running a Schwing every day, your parts kit should look like a maintenance schedule, not a wish list. I keep a spreadsheet of what each truck has burned in the last 12 months and stock against that. Sounds obsessive. It's saved me two missed pours in 18 months, so I'll take the nickname. And it matters for client perception—a pump that runs clean tells your customer you've got your operation together. A pump that dies mid-pour tells them something else.
What's the one thing you'd tell a first-time buyer?
Buy for the job, not the price tag. A pump truck that's $3,000 cheaper but needs $6,000 in hydraulic work isn't cheaper—it's just a delayed bill. I've watched that pattern play out maybe five times, and every time the buyer ends up back at the parts counter, sometimes within 90 days. Save yourself the loop. The cheap truck only feels cheap until the first repair bill lands.
